Free FE Other practice problems

Ten real questions from our FE Other Disciplines bank, drawn from 10 of its 14 study topics, with fully worked solutions and the same figures our members get. No signup, no email. Try each one first, then reveal the solution.

6 with figures10 topicsFull worked solutions

1
medium
A. DC circuits: Ohm's & Kirchhoff's laws, equivalents, Thevenin & Norton
A voltage divider made of $R_1=120\,\Omega$ and $R_2=300\,\Omega$ is supplied from a 24 V DC source, with its output taken across $R_2$ . A load $R_L=600\,\Omega$ is then connected across the output terminals, as shown. The voltage across the load is most nearly:
Figure — drag or pinch to move around
1. 15 V
2. 17.1 V
3. 20 V
4. 21.2 V
Show the answer & worked solution
Answer: A.15 V
The load is in parallel with $R_2$ , so the lower leg is $R_2\|R_L=\dfrac{300\cdot600}{300+600}=200\,\Omega$ , in series with $R_1$ (Resistors in Series and Parallel, FE Reference Handbook 10.6 p. 363). The source current is $I=\dfrac{24}{120+200}=0.075$ A, and Ohm's law across the lower leg gives $V_{out}=I\,(R_2\|R_L)=0.075\cdot200=15$ V. Distractors: the unloaded divider value, loading ignored ( $24\cdot300/420=17.1$ V); the load placed in series with $R_2$ instead of in parallel ( $24\cdot900/1020=21.2$ V); and the load taken as replacing $R_2$ rather than paralleling it ( $24\cdot600/720=20$ V).
2
medium
A. Time value of money, cost analysis, break-even & benefit-cost
An engineer borrows $200,000 to be repaid in 15 equal end-of-year payments at 6% per year. The annual payment is most nearly:
Figure — drag or pinch to move around
1. $8,593
2. $13,333
3. $20,593
4. $25,333
Show the answer & worked solution
Answer: C.$20,593
The capital recovery factor (FE Reference Handbook 10.6 p. 235) converts a present amount into equal end-of-year payments: $(A/P,\ 6\%,\ 15)=\dfrac{i(1+i)^n}{(1+i)^n-1}=\dfrac{0.06\,(1.06)^{15}}{(1.06)^{15}-1}=0.10296$ , printed as 0.1030 in the handbook's 6% factor table. The annual payment is $200,000 × 0.10296 = $20,593. Distractors: $P/n$ , spreading the principal evenly and ignoring interest ($13,333); the sinking-fund factor $(A/F)$ read in place of $(A/P)$ ($8,593), which treats the loan as a future sum; and simple interest on the full principal for all 15 years, spread evenly, $P(1+in)/n$ ($25,333), which charges interest on money already repaid.
3
medium
A. Fluid statics, Bernoulli, pipe flow, open channel, flow measurement & turbomachinery
Water flows steadily through a pipe that contracts from a diameter $D_1 = 200$ mm to $D_2 = 150$ mm. The upstream velocity is $V_1 = 1.5$ m/s. The velocity in the smaller section is most nearly:
Figure — drag or pinch to move around
1. 0.844 m/s
2. 2 m/s
3. 2.67 m/s
4. 4.74 m/s
Show the answer & worked solution
Answer: C.2.67 m/s
Continuity (FE Reference Handbook 10.6 p. 185): the same flow $Q=Av$ passes both sections, so $A_1V_1=A_2V_2$ . With $A=\pi D^2/4$ the $\pi/4$ cancels, leaving $V_2=V_1\left(\dfrac{D_1}{D_2}\right)^2=1.5\left(\dfrac{200}{150}\right)^2=2.67$ m/s, faster in the smaller section, as it must be. Distractors: the diameter ratio used un-squared, $V_1D_1/D_2$ (2 m/s), forgetting that area goes as $D^2$ ; the area ratio inverted, $V_1(D_2/D_1)^2$ (0.844 m/s), which would have the water slow down in the smaller section; and the ratio squared twice, $V_1(D_1/D_2)^4$ (4.74 m/s), the area-ratio squaring applied a second time.
4
medium
A. Stress & strain, bending, torsion, transformation, buckling & failure
A beam of solid rectangular cross-section, width $b=50\,\text{mm}$ and depth $h=100\,\text{mm}$ , carries an internal bending moment $M=5\,\text{kN}\cdot\text{m}$ . The maximum bending (flexural) stress is most nearly:
Figure — drag or pinch to move around
1. 10 MPa
2. 15 MPa
3. 40 MPa
4. 60 MPa
Show the answer & worked solution
Answer: D.60 MPa
Maximum bending stress (Mechanics of Materials — Stresses in Beams): $\sigma=\dfrac{Mc}{I}$ , with the centroidal $I=\dfrac{bh^3}{12}=\dfrac{(50)(100)^3}{12}=4.167\times10^{6}\ \text{mm}^4$ and $c=h/2=50\ \text{mm}$ , which for a rectangle is $\sigma=\dfrac{6M}{bh^2}$ . With $M=5\ \text{kN·m}=5\times10^{6}\ \text{N·mm}$ : $\sigma=\dfrac{6(5\times10^{6}\ \text{N·mm})}{(50\ \text{mm})(100\ \text{mm})^2}=60$ MPa. Distractors: used $I=bh^3/3$ , the area table's moment of inertia about the BASE, instead of the centroidal $bh^3/12$ (¼ of the true stress); dropped the factor 6 (used $\sigma=M/bh^2$ ); and divided by the plastic section modulus $Z=bh^2/4$ instead of the elastic $S=bh^2/6$ (two-thirds of the true stress).
5
medium
A. Force systems, equilibrium, trusses, friction & area properties
A simply-supported beam of span $L=6$ m carries a uniform load $w=4$ kN/m over its entire length plus a point load $P=12$ kN located 2 m from the left support (A). The pin reaction at A is most nearly:
Figure — drag or pinch to move around
1. 10 kN
2. 16 kN
3. 18 kN
4. 20 kN
Show the answer & worked solution
Answer: D.20 kN
Replace the uniform load by its resultant, $wL=(4\ \text{kN/m})(6\ \text{m})=24$ kN acting at midspan, 3 m from each support. Then take moments about the roller B, which removes $R_B$ (Statics — Equilibrium Requirements, $\Sigma M=0$ ): $R_A(6\ \text{m})=(12\ \text{kN})(4\ \text{m})+(24\ \text{kN})(3\ \text{m})$ , so $R_A=\dfrac{48+72}{6}=20$ kN. Check with $\Sigma F_y=0$ : $R_B=12+24-20=16$ kN. Distractors: the point-load moment arm taken as $a$ instead of $(L-a)$ — moments summed about the wrong support — yielding $R_B$ (16 kN); the point load split evenly regardless of its position ( $P/2$ , giving 18 kN); and the load intensity $w=4$ kN/m used as if it were the distributed load's resultant, instead of $wL=24$ kN, so A gets only $w/2$ from it (10 kN).
6
medium
A. Probability distributions, descriptive statistics & expected value
The life of a carbide cutting insert turning steel at a fixed cutting speed is normally distributed with mean $\mu=50$ min and standard deviation $\sigma=8$ min. The probability that a randomly selected insert lasts between 46 min and 62 min is most nearly:
Figure — drag or pinch to move around
1. 0.2417
2. 0.4332
3. 0.6247
4. 0.6915
Show the answer & worked solution
Answer: C.0.6247
Standardize each limit (Normal Distribution, $z=(x-\mu)/\sigma$ ): $z_a=(46-50)/8=-0.50$ and $z_b=(62-50)/8=1.50$ . From the Unit Normal Distribution table, $F(1.50)=0.9332$ and $F(-0.50)=1-F(0.50)=1-0.6915=0.3085$ (the table lists only positive $x$ ). So $P(46<X<62)=F(z_b)-F(z_a)=0.9332-0.3085=0.6247$ . Distractors: the minus sign on $z_a=-0.50$ dropped, so the table value $F(0.50)=0.6915$ was subtracted in place of $F(-0.50)=0.3085$ (0.2417); only the area from the mean to 62 min counted, $F(1.50)-0.5$ , leaving out the part between 46 min and the mean (0.4332); and the upper limit ignored, reporting $P(X>46)=1-F(-0.50)$ (0.6915).
7
medium
A. Stoichiometry, equilibrium, acids/bases, oxidation-reduction & gas laws
A technician adds 200 mL of 0.050 mol/L hydrochloric acid, a strong acid, to 300 mL of pure water. Taking the volumes as additive, the pH of the resulting solution at 25 °C is most nearly:
1. 1.30
2. 1.48
3. 1.70
4. 3.91
Show the answer & worked solution
Answer: C.1.70
Molarity is gram moles of solute per liter of solution (FE Reference Handbook 10.6 p. 86). The acid brings $0.050\times0.2=0.01$ mol of $\mathrm{H^+}$ (HCl dissociates completely) into $200+300=500$ mL of solution, so $[\mathrm{H^+}]=0.01/0.5=0.02$ mol/L. Then $\mathrm{pH}=\log_{10}(1/[\mathrm{H^+}])=-\log_{10}0.02=1.70$ (p. 87). Distractors: the dilution ignored, giving the pH of the 0.050 mol/L stock itself ( $-\log_{10}0.05=1.30$ ); the 300 mL of water taken as the final volume, leaving out the acid's own 200 mL ( $[\mathrm{H^+}]=0.0333$ mol/L, pH 1.48); and the natural log used in place of $\log_{10}$ ( $-\ln 0.02=3.91$ ).
8
medium
A. Kinematics, kinetics, work-energy, impulse-momentum & vibration
A 1200 kg car skids with its wheels locked along a level road, slowing from 20 m/s to 8 m/s. Neglecting air resistance, the magnitude of the work done on the car by friction during the skid is most nearly:
1. 86.4 kJ
2. 202 kJ
3. 240 kJ
4. 278 kJ
Show the answer & worked solution
Answer: B.202 kJ
Principle of work and energy (FE Reference Handbook 10.6 p. 107): $T_2=T_1+U_{1\to2}$ on a level road, with $T=\tfrac12 mv^2$ . $T_1=\tfrac12\cdot1200\cdot20^2=240$ kJ and $T_2=\tfrac12\cdot1200\cdot8^2=38.4$ kJ, so $U_{1\to2}=T_2-T_1=-201.6$ kJ: friction does 202 kJ of negative work. Distractors: the speeds subtracted before squaring, $\tfrac12 m(\Delta v)^2=\tfrac12\cdot1200\cdot12^2$ (86.4 kJ), which is not the change in kinetic energy; the final speed ignored, taking the whole initial kinetic energy $T_1$ (240 kJ) as if the car had stopped; and the two kinetic energies added instead of subtracted, $T_1+T_2$ (278 kJ), the sign of the work term mishandled.
9
medium
A. Codes of ethics, licensure, public protection & intellectual property
An engineer preparing the switchgear specification for a hospital project owns a 20 percent interest in one of the three manufacturers likely to bid on the equipment. Under the NCEES Model Rules of Professional Conduct, the engineer should:
1. disclose the ownership interest to the client in writing before continuing with the specification
2. sell the ownership interest quietly after the contract is awarded to eliminate the conflict
3. continue normally, since the bids will be evaluated against objective criteria the client controls
4. write the specification around generic performance requirements so the ownership has no practical effect
Show the answer & worked solution
Answer: A.disclose the ownership interest to the client in writing before continuing with the specification
Model Rule B.6 (FE Reference Handbook 10.6 p. 5, Obligations of Licensees to Employer and Clients) requires a licensee to disclose to the client all known or potential conflicts of interest that could influence or appear to influence their judgment. A stake in a likely bidder is exactly that, and the specification is where it could act, so the client must hear of it before the work goes further; putting it in writing makes the disclosure a record, and the informed client then decides how to proceed. Distractors: drafting around the interest manages the conflict privately, and the client still does not know of it; objective bid criteria do not cure it, because the stake can shape the specification itself before any bid is scored; selling the interest after award keeps the conflict hidden through the very period in which it could operate.
10
medium
A. Sensors, data acquisition, signal conditioning & logic
A pressure transducer has a linear output of 0.5 V at 0 kPa (gauge) and 4.5 V at 1,000 kPa (gauge). In service it reads 1.7 V. The gauge pressure is most nearly:
1. 267 kPa
2. 300 kPa
3. 378 kPa
4. 425 kPa
Show the answer & worked solution
Answer: B.300 kPa
Transducer sensitivity is the ratio of the change in output to the change in the measured quantity (FE Reference Handbook 10.6 p. 225): $S=\dfrac{(4.5-0.5)\ \text{V}}{(1000-0)\ \text{kPa}}=0.004$ V/kPa $=4$ mV/kPa. The output is the 0.5 V zero offset plus $S$ times the pressure, so $p=\dfrac{V-V_0}{S}=\dfrac{1.7-0.5}{0.004}=300$ kPa. Distractors: the 0.5 V zero output left in the reading, $1.7/0.004$ (425 kPa); the sensitivity taken as full-scale output over full-scale pressure, $4.5\ \text{V}/1000\ \text{kPa}=4.5$ mV/kPa, which counts the offset as signal (267 kPa); and the reading taken as a plain fraction of the full-scale output, $(1.7/4.5)\times1000$ (378 kPa), ignoring the offset in both.

That was ten. There are 1,600+ more.

The full FE Other Disciplines bank covers every knowledge area, with full-length timed mock exams at the real exam's 110 questions and time limit, and an AI tutor to talk any problem through.

Explore FE Other See pricing

Studying for a different exam? See free practice problems for all 11 exams, or read our FE & PE study guides.

These ten are among the free sample questions anyone can practice in the app, no account needed. The paid bank is separate. Independent study resource; not affiliated with, endorsed by, or sponsored by NCEES.